[RegCNET] problem running RegCM

[Dr. Md. Nazrul Islam]

Dear Satyaban,

I think you may reduce dt in regcm.in file say dt = 100.
I am using AMD64 machine and some times get same reminder "Floating 
exception". Usually I over come the dificulties by reducing dt.

Nazrul

Dr. Md. Nazrul Islam
Associate Professor
Department of Physics
Bangladesh University of Engineering and Technology
Dhaka-1000, Bangladesh
http://www.buet.ac.bd/phy/nazrul.htm

Phone: 880 2 966 5650 (PABX)
FAX: 880 2 861 3026, 880 2 861 3046


---------- Original Message -----------
From: "Satyaban Bishoyi Ratna" <satyaban_2001 at rediffmail.com>
To: "XUNQIANG BI" <bixq at ictp.it>
Cc: regcnet at lists.ictp.it
Sent: 27 Jun 2007 03:38:37 -0000
Subject: [RegCNET] problem running RegCM

> Dear Sir,
> As per your mail I followed the give suggestion but I
> didn't got any success.
> At first I tried with NORMER (instead of LAMCON) but no success.
> Later I tried with LAMCON, using 10N and 30N as truelatL and truelatH
> (instead of 30N and 60N) but no success.
> So finally I tried the model run with bydefault setup of 
> the Regcm which is available at ICTP. That means I didn't change in
> 'Terrain' and 'ICBC' setup for this run in my machine. Only I have 
> changed the 'Makefile' suitable to AMD64. I didn't got any error in 
> 'Terrain' and 'ICBC' run. But when I came to the main part of model 
> run the same error occured and it terminates the model run. I am 
> giving the lines here, which occured during the terminates of model run.
> I request you please look into this ang give me suggestion to run 
> the RegCM successfully.
> 
> Thanking you.
> Best regards
> Satyaban
> ...........
> ...........
> dectim = 1440.000000000000
> BCs are ready from 2005010100 to 2005010106
> dt, dtau = 150.0000000000000 37.50000000000000
> 75.00000000000000
> 0 linearization about standard atmosphere (lstand=.t.)
> 0sigmaf 0.000 5.000E-02 0.100 0.160 0.230 0.310 0.390 0.470 0.550 
> 0.630 0.710
> 0.780 0.840 0.890 0.930 0.960 0.980 0.990 1.00 0t mean 218. 218. 
> 218. 218. 229. 239. 248. 255. 262. 268. 273. 277. 280. 283. 285. 
> 286. 287. 287. 0ps mean 100. 0 vertical mode problem completed for 
> kx= 18 0 errors detected (should be 0) m, fac = 4 33.33333333333334 
> m, fac = 2 60.00000000000000 Writing output files in direct access format
> 
> ******* OPENING NEW OUTPUT FILES: 2005010100
> OPENING NEW OUT FILE: output/ATM.2005010100
> OPENING NEW BAT FILE: output/SRF.2005010100
> OPENING NEW RAD FILE: output/RAD.2005010100
> OUT-history written date = 2005010100.000000
> BATS variables written at 2005010100 2.500000000000000
> Writing rad fields at ktau = 1 2005010100
> at day = 0.0851, ktau = 50 : 1st, 2nd time deriv of ps = 0.24425E-04 
> 0.93659E-0 7, no. of points w/convection = 22 Floating exception 
mm5 at aucluster:~/RegCM/RegCM/Run$
> 
> On Tue, 26 Jun 2007 XUNQIANG BI wrote :
> >
> >Hi, Satyaban:
> >
> >The domain.param is not a right one.
> >
> >Three suggestion:
> >
> >1. Since the clat is quite close to Equaltor, you can try use
> > NORMER (instead of LAMCON).
> >
> >2. If you use LAMCON, try to use 10N and 30N as truelatL and truelatH
> > (instead of 30N and 60N)
> >
> >3. If you use FERRET, you can try also use ROTMER.
> >
> >Regards,
> >Bi
> >
> >~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~
> > Dr. Xunqiang Bi email:bixq at ictp.it
> > Earth System Physics Group
> > The Abdus Salam ICTP
> > Strada Costiera, 11
> > P.O. BOX 586, 34100 Trieste, ITALY
> > Tel: +39-040-2240302 Fax: +39-040-2240449
> >~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~
> 
> 
*****************************************************************************
***********************
> Satyaban Bishoyi Ratna
> Research Scholar
> Department of Meteorology and Oceanography
> Andhra University
> Visakhapatnam - 530003
> Andhra Pradesh, India
> Cell: 94403 30367
> E-mail: satyaban_2001 at rediffmail.com
> satyaban14 at yahoo.co.in
> 
> 
*****************************************************************************
***********************
------- End of Original Message -------