Dear all,
I was trying to run RegCM-4.3.5.6 with-CLM for resolution of 20km.
Pre-Processing succeed. While I got this error when I
start the model.
$: mpirun -np 12 regcmMPI_clm $namelist > runlog.$namelist 2>&1
————————————————————————————————————————
...
Attempting to read surface boundary data .....
(GETFIL): attempting to find local file t20km_RCMlanwat.nc
(GETFIL): using ./input/t20km_RCMlanwat.nc
(GETFIL): attempting to find local file t20km_RCMsoitex.10level.nc
(GETFIL): using ./input/t20km_RCMsoitex.10level.nc
(GETFIL): attempting to find local file t20km_RCMglacier.nc
(GETFIL): using ./input/t20km_RCMglacier.nc
(GETFIL): attempting to find local file t20km_RCMurban.nc
(GETFIL): using ./input/t20km_RCMurban.nc
(GETFIL): attempting to find local file t20km_RCMpft.nc
(GETFIL): using ./input/t20km_RCMpft.nc
surfrd error: WTXY > 1 occurs at nl= 20627
ENDRUN: called without a message string
application called MPI_Abort(MPI_COMM_WORLD, 1) - process 8forrtl: error (76): Abort trap signal
Image PC Routine Line Source
libc.so.6 0000003458830265 Unknown Unknown Unknown
libc.so.6 0000003458831D10 Unknown Unknown Unknown
libmpidev.so 00002ADB38EFE1EF Unknown Unknown Unknown
libmpi.so 00002ADB37935E47 Unknown Unknown Unknown
libmpi.so 00002ADB3793935D Unknown Unknown Unknown
regcmMPI_clm 000000000084A149 Unknown Unknown Unknown
regcmMPI_clm 000000000093E51D Unknown Unknown Unknown
regcmMPI_clm 0000000000949079 Unknown Unknown Unknown
regcmMPI_clm 0000000000911276 Unknown Unknown Unknown
regcmMPI_clm 00000000008E025A Unknown Unknown Unknown
regcmMPI_clm 000000000083EAEF Unknown Unknown Unknown
regcmMPI_clm 0000000000578DD3 Unknown Unknown Unknown
regcmMPI_clm 00000000006677E7 Unknown Unknown Unknown
regcmMPI_clm 0000000000667AE5 Unknown Unknown Unknown
regcmMPI_clm 000000000040C01C Unknown Unknown Unknown
libc.so.6 000000345881D994 Unknown Unknown Unknown
regcmMPI_clm 000000000040BF29 Unknown Unknown Unknown
rank 8 in job 1 titan21_36041 caused collective abort of all ranks
exit status of rank 8: killed by signal 9
————————————————————————————————————————
My domain size is 100 degree in longitude, 40 degree in latitude.
And, below is part of my namelist file,
————————————————————————————————————————
&dimparam
iy = 252, ! for 50km iy=96; for 20km iy=252
jx = 576, ! for 50km ix=224; for 20km ix=576
kz = 18,
nsg = 1,
/
&geoparam
iproj = 'NORMER',
ds = 20.0,
ptop = 5.0,
clat = -20.00,
clon = 50.00,
plat = -21.00,
plon = 55.00,
truelatl = 30.0,
truelath = 60.0,
i_band = 0,
/
…
&timeparam
dtrad = 30.,
dtabem = 18.,
dtsrf = 600.,
dt = 50.,
/
…
————————————————————————————————————————
The model runs successfully and reaches the end if I set iy = 96, jx = 224 (for 50km)
leaving other parameters ( ds, dt, ... ) unchanged.
Could you please give me some advise ? thanks.
Best regards,
Chao TANG
-------------------------------------------------------------------------------------------------
Laboratoire d'Energétique, d'Electronique et Procédés
Unité de Recherche EA 4079
Université de La Réunion, LE2P
15 avenue René Cassin CS 92003
97744 ST DENIS CEDEX 9
-------------------------------------------------------------------------------------------------