[RegCNET] new diag + enable output : re SST preproc fail

James Ciarlo` james.ciarlo at physics.org
Fri Apr 12 17:16:36 CEST 2013


Thanks Graziano and Ivan,

I will be conducting some tests to figure out the issues


On 12 April 2013 17:14, Ivan Guettler <ivan.guettler at gmail.com> wrote:

> Enjoy! :)
>
> Ivan
>
> 2013/4/12 James Ciarlo` <james.ciarlo at physics.org>:
> > Can someone send me a working regcm.in file for RegCM4.4 so that I can
> > experiment a bit and possibly figure out this problem
> >
> >
> > On 8 April 2013 14:48, James Ciarlo` <james.ciarlo at physics.org> wrote:
> >>
> >> Hi Dr Solmon,
> >>
> >> I added the idiag = 1 in the outparam, but the errors are still the same
> >>
> >> Regards
> >>
> >>
> >> On 5 April 2013 14:09, Solmon Fabien <fsolmon at ictp.it> wrote:
> >>>
> >>> Hello !
> >>>
> >>> For general information, in the last release candiate regcm 4.4 (beta)
> ,
> >>> there is a new possibility of saving and outputing every term of the
> the
> >>> temperature tendency (adv,dif,conv,turb, bdy etc ) as part of the ATM
> file.
> >>> This option is enabled if idiag=1 in the outparam nameliste.  In this
> case
> >>> there are 7 additional 3d variable in addition  to the normal  output
> >>> containing 10 variables.
> >>>
> >>> In addition there is also the possibility to specify outputs we want in
> >>> the files using the logical table : enable_atm_var , still in the
> outparam
> >>> namelist.
> >>>
> >>> Now in response to James email :  I saw that in your regcm.in you have
> >>> used the option to enable 17 ATM outputs by setting the enable_atm_var
> to
> >>> 17*.true., however you did not enable the idiag option ... there might
> be a
> >>> problem here, we need to double check.
> >>>
> >>> best regards
> >>> Fabien
> >>>
> >>>
> >>>
> >>>
> >>> On 03/28/2013 07:58 PM, James Ciarlo` wrote:
> >>>
> >>> Hi,
> >>>
> >>> I am trying to run a basic simulation with the attached regcm.in file,
> >>> but I am getting an error that I cannot recognise that seems to be
> related
> >>> to the SST.
> >>>
> >>> The error seems to happen during the preproc of ssts.
> >>>
> >>> Regards,
> >>> James
> >>>
> >>>
> >>> _______________________________________________
> >>> RegCNET mailing list
> >>> RegCNET at lists.ictp.it
> >>> https://lists.ictp.it/mailman/listinfo.cgi/regcnet
> >>>
> >>>
> >>>
> >>> --
> >>> ---------------------------------------------------
> >>> Fabien Solmon
> >>> Research Scientist
> >>> +39 040 2240206 (office) | Earth System Physics
> >>> +39 040 2240449 (fax)    | ICTP (UNESCO-IAEA)
> >>> esp.ictp.it              | Strada Costiera 11
> >>>                          | 34014 Trieste, Italy
> >>>
> >>>
> >>> _______________________________________________
> >>> RegCNET mailing list
> >>> RegCNET at lists.ictp.it
> >>> https://lists.ictp.it/mailman/listinfo.cgi/regcnet
> >>
> >>
> >
> >
> > _______________________________________________
> > RegCNET mailing list
> > RegCNET at lists.ictp.it
> > https://lists.ictp.it/mailman/listinfo.cgi/regcnet
>
>
>
> --
> Ivan Guettler
> Ph.D. student
>
> Meteorological and Hydrological Service of Croatia
> Department for Climatological Research and Applied Climatology
>
> Gric 3, 10000 Zagreb, Croatia
> e-mail: ivan.guettler at cirus.dhz.hr, ivan.guettler at gmail.com
> https://sites.google.com/site/ivanguettler
> Tel: + 385 1 4565 638
>
-------------- next part --------------
An HTML attachment was scrubbed...
URL: <https://lists.ictp.it/pipermail/regcnet/attachments/20130412/e125b300/attachment.htm>


More information about the RegCNET mailing list